WWT Shows CLICK TO: Join and Support Internet Horology Club 185™ IHC185™ Forums

• Check Out Our... •
• TWO Book Offer! •
Welcome Aboard IHC185™     Internet Horology Club 185    IHC185™ Discussion Site Main Page  Hop To Forum Categories  Technical, Shop Talk and Internet Links  Hop To Forums  Watch Repair Questions and Answers    Hamilton 927 loses beats then settles down... fixed - main spring lesson learned
Go
New Topic
Find-Or-Search
Notify
Tools
Reply to Post
  
Hamilton 927 loses beats then settles down... fixed - main spring lesson learned "Click" to Login or Register 
IHC Member 1736
posted
I just COA'd a 927 I bought for my father. On a fresh wind, it runs at 18000 in positions, as expected... but after a few minutes, it drops to 17980 and settles down... an hour later it is settled out at 17960... and after a few hours drifts all the way down to 17500... where it stays for the rest of the day.

The only other main spring I have is a "good, used spare"... it is a bit better, but still similar in behavior...

I've ordered a new alloy main spring... outside of a fresh main spring... I'm not sure what to look for.

If I give it a couple clicks on the winder, it will speed back up for a bit... but then drifts back down to the lower speed.

The crazy thing is, the watch has above average to great motion on the balance wheel, all the way down... if I have 270 at 18,000... I still have around 200 degrees at 17,500... and the audio is still crisp... the beat error is not affected.
 
Posts: 2032 | Location: San Diego, California in the USA | Registered: August 30, 2012
IHC Member 456
posted
Check to see if the hairspring is snug between the regulator pins.
 
Posts: 541 | Location: Mohrsville, Pennsylvania U.S.A. | Registered: February 15, 2005
IHC Member 1736
posted
This main spring had enough power to run the watch, but fell off dramatically over the course of a few hours.

The problem is, that I poised and timed the watch with this spring... a 926 does not have timing screws... so, I had removed two timing washers and under cut two screws to time the watch... then, as the watch ran... it would drop from 18,000 to 17980 to 17950 and on down 'till it settled out around 17500 'till it ran out of reserve...

When I put a new alloy main spring in, it came back to life at 18030bph and stayed there... I had to add timing washers back in to get her to settle out at 18000... she holds 18000 plus or minus 1 beat in any position with the new spring now.

 
Posts: 2032 | Location: San Diego, California in the USA | Registered: August 30, 2012
IHC Member 1736
posted
Great dial and hands

 
Posts: 2032 | Location: San Diego, California in the USA | Registered: August 30, 2012
IHC Member 1736
posted
Very clean an nicely detailed movement

 
Posts: 2032 | Location: San Diego, California in the USA | Registered: August 30, 2012
IHC Member 1291
Picture of Buster Beck
posted
A lot of us, like mainsprings, get set in our ways, maybe begin to slip a little or sometimes get wound too tight, especially after we have been around for 50 or more years.....

Perhaps that is what is wrong with some of us "oldsters", we need a new mainspring !! I'm sure I qualify and I demand my "senior discount" to boot and I want it now !!!!

Nice looking watch.

regards,
bb
 
Posts: 6376 | Location: Texas in the USA | Registered: July 27, 2009
IHC Member 1736
posted
Thank you for the affirmation and the chuckle Buster... Reminds me of going to lunch with my dad... we used to get all philosophical over who was paying... now, I just reach for my wallet.
 
Posts: 2032 | Location: San Diego, California in the USA | Registered: August 30, 2012
Picture of Dave Turner
posted
You wanta go to lunch?


Dave Turner
 
Posts: 1979 | Location: Wilson, North Carolina in the USA | Registered: November 15, 2011
  Powered by Social Strata  
 

Welcome Aboard IHC185™     Internet Horology Club 185    IHC185™ Discussion Site Main Page  Hop To Forum Categories  Technical, Shop Talk and Internet Links  Hop To Forums  Watch Repair Questions and Answers    Hamilton 927 loses beats then settles down... fixed - main spring lesson learned

©2002-2023 Internet Horology Club 185™ - Lindell V. Riddle President - All Rights Reserved Worldwide

Internet Horology Club 185™ is the "Family-Friendly" place for Watch and Clock Collectors